Mike69 wrote: Chewy_719 wrote: Mike69 wrote: Chewy, if you want a heavier duty bar to mount your lights on try the one I have on my 2000 Ranger. ...   Tue Jan 21st, 2020 11:13 pm

Mike69 wrote: Chewy, if you want a heavier duty bar to mount your lights on try the one I have on my 2000 Ranger. I purchased ...   Tue Jan 21st, 2020 03:26 pm

This was one of my hunting trips, but didn't have any luck. ...   Sun Jan 19th, 2020 03:38 pm

I've put the mirrors and the KC lights on. The mount for the lights is horrible. Off road they just bounce around. ...   Sun Jan 19th, 2020 03:36 pm

Haven't done much to it since the trucks been running super rich on one side and lean on the other. That took a while to ...   Sat Jan 18th, 2020 08:07 pm

Project update: Just spent $43 on new mirrors for the ranger. 06+ mirror mod. Hopefully soon I can replace the intake manifold gaskets and injector o-rings ...   Fri Jul 5th, 2019 05:16 pm

Project update: Just spent $43 on new mirrors for the ranger. 06+ mirror mod. Hopefully soon I can replace the intake manifold gaskets and injector o-rings ...   Fri Jul 5th, 2019 05:11 pm

I talked to one of my buddies I served with and he agrees that it's a vacuum leak, so I'll be replacing the intake gaskets ...   Tue Jun 4th, 2019 09:28 am

Yes I have a OBD2 scanner ...   Sat Jun 1st, 2019 07:23 pm

Well I attempted to check the compression but I need a different tester. The one I have is difficult to get in to test.  But I ...   Sat Jun 1st, 2019 04:23 pm

410customs wrote: Sometimes when changing injectors that's when the problem starts...they must be installed properly and with good seats and O rings. It is very easy ...   Fri May 31st, 2019 12:07 pm

410customs wrote: Why did he replace injectors? Chasing the same codes? What year is your ranger? It's a '98. I don't know why he replaced them. There is ...   Tue May 28th, 2019 02:22 pm

410customs wrote: It happens, especially with ethenol blended fuel Check fuel rail pressure to ensure you do not have a pressure regulator issue Listen to the injectors click/ ...   Tue May 28th, 2019 12:52 pm

I have replaced to O2 sensor and cleared the codes, but they came back. I was not able to check the compression of each cylinder. ...   Tue May 28th, 2019 09:34 am

410customs wrote: I have stretched out two different 02 sensor sockets to the point of them being un-usable. I prefer the 02 sensor wrench head (like ...   Wed May 22nd, 2019 09:34 am

410customs wrote: what are the codes? The codes I have: P0175 Bank 2 System too Rich P1152 Lack of Heated Oxygen, Bank 2 These codes are in the PCM 2 ...   Tue May 21st, 2019 09:38 am

JAMMAN wrote: Didn't want to advise something shady, but I knocked the insides out of the cats on one and woke it right up. No CEL ...   Tue May 21st, 2019 09:35 am

410customs wrote: for power in the high rockies of Colorado there are a couple of things you can do no matter what engine you have. Getting ...   Tue May 21st, 2019 09:33 am

I have the P1000 code and I'll scan it tomorrow before work and put them in here. ...   Mon May 20th, 2019 11:16 pm

Ok so I have 5 codes that popped up and all of them have to do with the O2 sensor reading RICH and VERY RICH. ...   Mon May 20th, 2019 07:12 pm

I didn't know where to put this so here it is. Over the weekend I took my Ranger on a little 180 mile trip and found ...   Mon May 20th, 2019 01:46 pm

Well I put them on my bumper. I ended up getting a universal light mount that mounts on your license plate. It doesn't look bad. ...   Wed May 8th, 2019 10:14 pm

When i flush my brakes and clutch I will let y'all know how it goes. With the warm weather its working perfectly fine, but the ...   Mon May 6th, 2019 10:05 am

Does anyone know why it would be hard to stop in cold weather. I never experienced this until today in any vehicle. We had some ...   Tue Apr 30th, 2019 11:03 pm

Scrambler82 wrote: Chewy_719 wrote: Scrambler82, I will installing only two Daylighters for now, with the wiring harness the kit cam with. Later on i will be adding LED ...   Mon Apr 29th, 2019 10:14 am

What's the LED number for the middle bulb which is a 212-2. I can't really find an LED replacement. ...   Sun Apr 28th, 2019 01:02 am

I will be doing this. Just replaced the ball joints on my truck and found out all the vacuum lines are rotted out. I wish ...   Sun Apr 28th, 2019 12:52 am

jkeaton wrote: Welcome! Thanks ...   Fri Apr 26th, 2019 12:26 pm

Scrambler82, I will installing only two Daylighters for now, with the wiring harness the kit cam with. Later on i will be adding LED bed lights ...   Fri Apr 26th, 2019 12:14 pm

Scrambler82 wrote: Chewy_719, Any thoughts so far, I know it hasn't been long for the Poll but what are your ideas. I think I'm going to go with ...   Fri Apr 26th, 2019 09:59 am

I'm trying to figure out what's going on with my ranger and I'm watching the short term and long term fuel trim. Can anybody explain ...   Tue Apr 23rd, 2019 09:12 pm

Ok, the leak is somewhere on the back of the upper intake manifold. Just replaced the PCV it was $2. If it's not that then ...   Tue Apr 23rd, 2019 08:18 pm

Scrambler82 wrote: Chewy_719 wrote: Thanks, I usually try to take my time when fixing something and trying to keep track of nuts and bolts. I will be ...   Tue Apr 23rd, 2019 05:20 pm

Thanks, I usually try to take my time when fixing something and trying to keep track of nuts and bolts. I will be hoking the ...   Tue Apr 23rd, 2019 11:38 am

I have the 3.0, but i can still check the torque on the intake. I'm going to use starter fluid and my scan tool and ...   Tue Apr 23rd, 2019 09:57 am

Scrambler82 wrote: Good base to start from. KC Daylighters... how many, how's the battery, alternator ? You willed to fortify the charging system to support the lights. 150 watt ...   Tue Apr 23rd, 2019 01:27 am

I am trying to figure our the best options on where to mount my KC lights. I have room on my bumper for them but ...   Mon Apr 22nd, 2019 06:58 pm

Thanks. I was surprised when I bought it on well of a condition it was in especially since it was a construction truck. ...   Mon Apr 22nd, 2019 04:49 pm

I will definitely do this. That is honestly the first time I have heard to connect the positive and negative wire together to drain the ...   Mon Apr 22nd, 2019 04:32 pm

Hey everyone, This is my first Ranger that I plan to modify a little to go up in the mountains with for hunting. I have KC ...   Mon Apr 22nd, 2019 04:13 pm