That makes perfectly good sense.  Thanks so much for the insight.  I removed the electric motor and drive assembly from the TC and took it ...   Mon Jun 22nd, 2020 12:28 pm

I would love to do the helicopter tour, but I would have to go by myself.  Dear Wife likes to keep her feet on the ...   Fri Jun 12th, 2020 12:14 pm

Thank you so much for all the great information!  I am a pure heathen dog for not getting back to you sooner, but life gets ...   Tue Jun 9th, 2020 12:39 pm

Appreciate the great tip on the trans tail housing, as well as all the other good stuff. All valuable information!  More than kind of you to ...   Sat Mar 21st, 2020 05:35 pm

Thanks so much for all of the insight on this problem.  I have felt all along that the trans failure was because of the towing, ...   Sat Mar 21st, 2020 02:30 pm

Greetings to all!  Hope you are faring well through the Virus excitement. I am in the beginning stages of a clutch/transmission replacement and hoping to convert ...   Fri Mar 20th, 2020 01:07 pm

Greetings all! My old ranger has been running great, but I had been trying to track down a high frequency vibration issue.  Narrowed it down to ...   Thu Sep 19th, 2019 07:11 pm

I have been off the site for awhile.  I have my ups and downs with my treatment cycles and all of the life that gets ...   Sun Aug 25th, 2019 08:35 pm

Just a note to say that you can add me to the list of folks who like the KYB Excel G shocks!  I put a ...   Mon Feb 18th, 2019 07:04 pm

You and Eddie Money are right on the mark.  Great trucks! We just got back from a 1500 mile road-trip and the truck did just fine.  ...   Fri Dec 7th, 2018 09:51 pm

Thanks for putting that out there.  I couldn't access it with the info I had.  Things change. ...   Wed Nov 14th, 2018 07:43 pm

That's ok, sometimes the details get a little fuzzy.  Actually, after I fixed the first problem I did get a check engine light and when ...   Wed Nov 14th, 2018 06:59 pm

Early on in the adventure, I thought about just replacing all of the relays because they were all original and 20 years old.  I would ...   Wed Nov 14th, 2018 06:37 pm

Thanks for the delete. ...   Wed Nov 14th, 2018 06:34 pm

Thanks much.  I don't have to tell you how frustrating some of these projects can be.  I connected the voltmeter at the inertia switch location. Good ...   Wed Nov 14th, 2018 06:32 pm

Hello all!  Wishing everyone a happy Thanksgiving and good times with family. It has been awhile since I last posted on my original problem of the ...   Wed Nov 14th, 2018 12:12 pm

Those plugs were on the passenger side.  The two over-heated plugs were only halfway in.  The driver's side plugs should show up below. ...   Wed Jul 4th, 2018 09:19 pm

Well, it has been a week and so far the truck has run great.  Good starts better power and driveability.  My first time to try ...   Wed Jul 4th, 2018 09:16 pm

I have an update on my engine shut-down problem, but first, thank you all for the feedback.  It has been very helpful. Based on some information ...   Tue Jun 26th, 2018 12:01 pm

Yeah, you right.  I just thought I would see if anyone happened to have the same issue.  Actually, I just ordered a Lemur BlueDriver OBD2 ...   Fri Jun 15th, 2018 01:50 pm

I am new to the forum and didn't think I would be needing a hand this soon, but, here goes.  I have a 1998 Ranger ...   Thu Jun 14th, 2018 01:11 pm

Thank you! ...   Fri May 18th, 2018 09:04 pm

Thanks for the welcome.  No, we found one on our travels from Florida to Texas and bought it on the way out.  I guess I ...   Fri May 18th, 2018 09:02 pm

Jumping in here, too!  Thanks to JAMMAN for the invite and hello to all. Recently replaced our trusty old Jeep(a nice young lady in Central Florida ...   Fri May 18th, 2018 08:44 pm