Ford-Rangers.com Ranger Forum HomeFord-Rangers.com Ranger Forum Home
Home Recent Topics New posts Search search Menu menu Not logged in - Login | Register
Ford-Rangers.com Ranger Forum > Tech Section > Electrical Tech > How to Calculate the Run Times of Your B

Ford-rangers.com is a discussion forum, a Ranger forum for people who have questions about fixing or modifying
their Ford Rangers or people who just admire their Ranger. Please join and enjoy sharing experiences!

How to Calculate the Run Times of Your B       #: 211
 Moderated by: NoPower, Mike69, MaDMaXX,
New Topic Reply
 Rate Topic 
 Posted: Tue Nov 21st, 2017 02:02 am
PM Quote Reply
1st Post
Undrstm8ed
Seasoned...


Joined: Sat Oct 21st, 2017
Posts: 1311
Name: 
Occupation: 
Interests: Life, Experiences, and adventures. ...
Status: 
Offline
Reputation: 
Reputation Points: 1311
Those figuring out secondary battery setups or situations may find this information more useful than say the guy wanting to see how long his system will play with the engine off and on Accessory..




How long your appliance will operate from a particular battery is dependent on the appliance's power consumption in watts (or AC amps x 115V), and the battery capacity. Low inverter efficiency, and improper battery wiring during installation can also reduce run time.
Calculating Run Time The following formula can be used to determine run time in most applications using a 12V battery or bank:





Example:
How long will my 100 watt TV run with my 150w inverter from my car's engine start battery (60 Ah)?
The load is well within the our inverter's maximum power rating, therefore the inverter itself will not limit the run time.









Engine start batteries should not be discharged below 90% remaining charge-state, and marine deep cycle batteries should not be discharged below 50% remaining charge state. Doing this will shorten the life of the battery based on most battery manufacturers' recommendations.
Some power invertors come factory equipped with a lighter plug for easy connection of smaller loads. However, for loads above 100W you will require direct connection to the battery terminals to eliminate a thin/long battery wire voltage loss that could drastically shorten the run time on a given system.
If you intend to use power tools for commercial use, or any load of 200W for more than 1 hour regularly (between battery recharging) you should install an auxiliary battery to provide power to the inverter. This battery should be a deep cycle type and sized to meet your run time expectations with the engine off. Deep cycle batteries most commonly available are 27 (90 Ah), 4D (150 Ah), 8D (220 Ah) capacity.

The auxiliary battery should be connected to the alternator through an isolator module to prevent the inverter from discharging the engine start battery when the engine is off.


Hope this helps others...

Last edited on Tue Nov 21st, 2017 02:03 am by Undrstm8ed



____________________
"Be never first, never last and never noticed." - Unknown

"The slave is held most securely when he is held by the chains of his own will and of his own fears, and when he is locked down by his own slavish desires for a comfortable life." - Michael Bunker

"Mundus vult decipi, ergo decipiatur" - ~ attributed to Petronius (Gaius Petronius Arbiter (ca. 27–66 AD))
Roman courtier during the reign of Nero.

"Those who expect to reap the blessings of freedom, must, like men, undergo the fatigue of supporting it." - Thomas Paine


~ Undrstm8ed Truckumentry Write Up Pg.

~ Undrstm8ed Trailermentry Write Up Pg.
.
Back To Top PM Quote Reply

 Posted: Thu Nov 23rd, 2017 04:25 pm
PM Quote Reply
2nd Post
12° North Industries
SITE SPONSOR


Joined: Thu Nov 23rd, 2017
Location: Las Vegas, USA
Posts: 393
Name: 
Occupation: Vehicle Upfitter ...
Interests: The great outdoors, nature, back to basics ...
Status: 
Offline
Reputation: 
Reputation Points: 393
Nice work!



____________________
North Industries
Las Vegas, Nevada 89118
Web http://www.12degnorth.com


Back To Top PM Quote Reply

Current time is 09:49 am Top  

Ford-Rangers.com Ranger Forum > Tech Section > Electrical Tech > How to Calculate the Run Times of Your B

Users viewing this topic



PHP Version: 8.3.33
Server version: 11.4.13-MariaDB
UltraBB 2.01.01 Copyright © 2008-2026 Jim & Chris
Page processed in 0.0351 seconds (52% database + 48% PHP). 38 queries executed.