| PM | Quote | Reply | Full Topic |
Joined: Mon Nov 13th, 2017
Location: Pacific North West
Posts: 1587
Status:
Offline
Reputation: 
Reputation Points: $user_rep
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Final torque on front suspension so we can mount some wheels and roll her into bay 1 on the lift
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]so earlier we installed camber shim adjusters on UCA heim joints
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]It was pointed out to me earlier in the thread that the True Travel kit needs the heim joints threaded basically all the way in to get decent camber readings.
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]I found this to be true.
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]A little bit of a pita to remove the upper camber shims/bolts.... remove UCA from mounts, loosen jamb nuts and run them all in....
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Done now and we have acceptable camber for a prelim alignment
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Jacks were used to bring control arms up and the king coil overs took the weight of the truck, this is somewhere around our final ride height. Lower balljoint/uniball and upper uniball were torqued to 140 ft lbs. Lower control arm and upper camber shims tightened also to 140, CV axle nut torqued to 220.
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Ready for tires!
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Each time the upper control arm heims need adjusting all of this must be removed, I'm hoping camber and caster are within spec and I wont have to do this again.
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Way too far out, all 4 heims were threaded all the way in
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]better
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Heim jamb nuts torqued down, camber shims back in place
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]
____________________
I know my crazy! Do you?
2007 Sport 4door 4x4 4.0L SOHC V6 Ranger